Home Things

Drywall, otherwise known as gypsum wallboard, has replaced plaster as the most common wall surface in American homes. It is used as a backing for wall treatments such as wallpaper, fabric, tile and wood paneling. Or it can simply be painted. Drywall has the virtue of being easy and inexpensive to install.

Repair

To fix nails that have popped from drywall, make sure the panel is secured to the studs above and below the nail. Hammer the nail in and dimple the nail; drive in and dimple a nail of the same size right next to it to hold it in. Use joint compound to cover the nails. When that has dried, sand the area, prime, and paint.

To fix small holes in your dry wall, clean the holes and dampen them with a sponge. Fill the holes with spackling compound using a narrow putty knife. You can also use patching plaster to fill the holes. Let the spackling compound dry, prime, and paint to match the rest of the wall.

Some large holes in wallboard can be patched with precut, adhesive wallboard patches. You may need to widen the hole so the patch can fit. After you have popped it in, cover the seams and the patch with joint compound, according to label directions, then prime with a wallboard primer and paint the surface.

Joe Kahler is recognized as an expert on helping young adults successfully transition from home to being “out on their own”. His latest work has recently been assembled in his book, Out On My Own… Now What? Tips and Insights So You Won’t Be Left Hanging in the “Real World”!

Joe received his undergraduate degree from Whittier College in Social Sciences and his Masters in Education from Arizona State University. His experience includes teaching, coaching, running numerous businesses, investing, selling insurance and real estate AND attending numerous personal, “hard knocks” training classes!

http://www.outonmyown.com

Share This

Hanging drywall is almost an art. Just ask anyone who does it professionally and they’ll tell you that it takes years of practice to do a perfect job. If you’re lucky enough, you might even get a few drywall finishing tips out of the conversation. If not, don’t worry. Here are some drywall finishing tips that everyone can benefit from!

Make Sure You Have Everything Before You Start

Drywall finishing tip #1: You need to have at hand a taping knife spreader, application knife, joint tape, joint compound, bread pan and a corner taping tool.

Get Secure About What You’re Doing

Drywall finishing tip #2: Drywall demands that all your measurements are accurate and that every panel is tightly secured to the supports that it’s nailed to. Could there be anything more embarrassing than to complete a drywall job - only to have it unexpectedly fall down during dinner or entertaining guests?

Make sure that your nails are long enough to keep the panels on their supports. If you’re more comfortable with using screws, then use them instead. You could even use a second set of nails as reinforcement. The important thing as that you feel as secure about your project as they’re secured to its foundation!

Beware A Muddy Mess

Drywall finishing tip #3: When mixing your cement (or mud), strive for a consistency that resembles icing on a cake - not too stiff and not too loose. Essentially, you should be able to scoop some of this mud onto a trowel, hold the trowel upside down, and not lose any of the cement. At the same time, you should also be able to easily apply this cement into drywall joints without too much effort.

While mixing, take care not to “whip” the cement. A whipping action will inadvertently attract air - air which will form bubbles in drywall seams.

Mesh Your Work Into A Smooth Finish

Drywall finishing tip #4. Use mesh tape instead of paper tape. Because mesh tape is porous, it allows the cement to seep through it. The end result is much smoother than paper which is sometimes visually apparent.

Use More Glue And Save On Nails

Drywall finishing tip #5: Use an adhesive to hold panels in place. Although this technique can’t and should never be used on the ceiling, you’ll only need to insert nails at the edges of drywall panels.

Give Your Drywalls A Little Dimple

Drywall finishing tip #6: You can hid the heads of your nails by hammering them in just below the surface of the drywall. This might take a little practice beforehand, as you don’t want the nail heads to show, but on the other hand, you don’t want to break the surface of the drywall either!

Patch Like A Pro

Drywall finishing tip #7: Stuffing a hole with newspaper tends to leave weak spots on a wall. Instead, cut a sizeable circle around a hole that needs patching. Insert a support piece that will fit behind the hole, and then glue it in place with cement. After about three hours, use even more cement to adhere a small piece of drywall to the support piece you inserted earlier. When dry, cover the hole with more cement and tape. You want to continue this process in the same manner as if you were concealing a joint.

Visit http://www.onlinetips.org, and learn about automatic drywall taping tools and outside corner drywall joints.

Share This